features low cost this series is ul recognized under component index, file number e127707 high forward surge current capability low thermal resistance. high isolation voltage from case to leads. high temperature soldering guaranteed: 260 /10 second, at 5 lbs. (2.3kg) tension. mechanical data case: metal case terminal: plated 0.04" (1.02mm) lug. polarity: polarity symbols marked on case. mounting: thru hole for #10 screw, 20 in,- lbs. torqute max. weight: 0.93 ounce, 26.4gram maximum ratings and electrical characteristics ratings at 25 ambient temperature unless otherwise specified single phase, half wave, 60hz, resistive or inductive load. for capacitive load derate current by 20% kbpc kbpc kbpc kbpc kbpc kbpc kbpc 35005w 3501w 3502w 3504w 3506w 3508w 3510w mb3505w mb351w MB352W mb354w mb356w mb358w mb3510 w v rrm 400 volts maximum rms voltage v rms
280
volts maximum dc blocking voltage v dc 400 volts maximum average forward rectified output current, at t c = 50 (note 1,2) peak forward surge current 8.3ms single half sine - wave superimposed on rated load (jedec method ) rating for fusing (t<8.3ms) i 2 ta 2 s per bridge element at 17.5a maximum dc reverse current at rate d t a = 25 a dc blocking voltage per element t a
ma isolation voltage from case to leads. v iso v ac typical thermal resistance r /w operating temperature range t j storage temperature range t stg 1. unit mounted on 9" x 3.5" x 4.6" (23cm x 9cm x 11.8cm)al. finned plate. 2. bolt down on heat-sink with silicon thermal compound between bridge and mounting sutfae for maximum heat transfer efficiency with # 10 screw. i (av) single-phase bridge rectifier maximum instantaneous forward voltage drop 2.0 (-65 to +150) (-65 to +150) amps v f i r volts i fsm a mps symbols unit maximum repetitive peak reverse voltage mb3505w-3510w http:// www.wej.cn e-mail:wej@yongerjia.com wej electronic co. r o hs wej electronic co.,ltd
a v e r a g e p o w e r d i s s i p a t i o n o f b r i d g e , j u n c t i o n c a p a c i t a n c e , ( p f ) revrese voltage,(v) j t =25 c 0.1 10 1.0 f=1mhz v sig p-p =50mv 100 average output current , 10 100 0 5 0 20 ( w ) 40 60 80 20 10 15 30 25 or resistive load inductive 35 j j max load capacitive t =t per bridge lement fig.3-typical forward characteristics 1%duty cycle pulse width=300us 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 inductive or resistive fig.1-derating curve for case temperature, ( c) output rectified current instantaneous for ward volt age,(v) fig.5-typical junction capacitance i n s t a n t a n e o u s f o r w a r d c u r r e n t , 1000 0.01 0.1 ( a ) 1.0 100 10 a v e r a g e f o r w a r d o u t p u t 0 0 50 10 20 c u r r e n t , ( a ) half wave 60hz single phase load 30 35 percent of rated peak reverse voltage,(%) 40 fig.6-maximum power dissipation i n s t a n t a n e o u s r e v e r s e c u r r e n t , 100 0.01 0 20 0.1 j t =25 c ( u a ) 1.0 10 100 100 60 80 120 140 j t =25 c j t =100 c fig.4-typical reverse characteristics forward surge current per element number of cycles at 60 hz fig.2-maximum non-repetitive peak 500 p e a k f o r w a r d s u r g e c u r r e n t , ( a ) 125 2 1 0 4 400 200 100 300 1 cycle heat sink mounting 600 700 6 8 10 20 40 60 100 t 8.3ms single half sine-wave (jedec method) =t j j max 9"x 3.5"x 4.6" thick (23 x 9 x 11.8cm) al.finned plate per bridge element per bridge element 25 75 100 150 175 (a) mb35 05 w -3510 w http:// www.wej.cn e-mail:wej@yongerjia.com wej electronic co. r o hs wej electronic co.,ltd
|
